Chevrolet Cruze manuals

Chevrolet Cruze Repair Manual: Brake Pedal Position Sensor Calibration

Chevrolet Cruze Repair Manual / Body systems / Lighting / Brake Pedal Position Sensor Calibration

Calibration Criteria

Note: Do not apply the brake pedal during the brake pedal position (BPP) sensor calibration procedure. Any movement of the brake pedal during this procedure will cause the calibration procedure to fail. If this occurs, the sensor calibration must be repeated.

Brake pedal position (BPP) sensor calibration must be performed after the sensor or body control module (BCM) have been serviced. The calibration procedure will set the sensor home value. This value is used by the BCM to determine the action of the driver applying the brake system and to provide this information to the vehicle subsystems via serial data.

Calibration Procedure

  1. Apply the parking brake.
  2. Place the transmission in the PARK position.
  3. Install a scan tool.
  4. Clear all BCM DTCs before proceeding.
  5. Navigate to the Vehicle Control Systems menu.
  6. Select Module Setup menu item.
  7. Select BCM menu item
  8. Select the BPP Sensor Calibration procedure and follow the directions displayed on the screen.

Brake Pedal Position Sensor Replacement

Preliminary Procedure

Preliminary Procedure

Remove the instrument panel lower trim pad cover. Refer to Instrument Panel Lower Trim Pad Cover Replacement.

  1. Brake Pedal Position Sensor Bolt

Caution: Refer to Fastener Caution in the Preface section.

Tighten 2 N·m (18 lb in)

  1. Brake Pedal Position Sensor

Procedure

  1. Disconnect 1. the electrical connector.
  2. Calibrate the brake pedal position sensor. Refer to Brake Pedal Position Sensor Calibration.

Headlamp Switch Replacement (Right Hand Drive)

Headlamp Switch Assembly

Headlamp Switch Assembly

Procedure

  1. Open the compartment to remove the headlamp switch.
  2. Disconnect the electrical connection.

Fog Lamp Switch Replacement (Right Hand Drive)

Fog Lamp Switch

Fog Lamp Switch

Procedure

  1. Disconnect   the electrical connection.
  2. Squeeze tabs on switch to unsnap from housing bracket.

Hazard Warning Switch Replacement

Preliminary Procedure

Preliminary Procedure

Remove instrument panel accessory bezel. Refer to Instrument Panel Accessory Bezel Replacement.

Hazard Warning Switch

Procedure

  1. Disconnect the electrical connection.
  2. Unsnap switch from instrument panel accessory bezel.

Instrument Panel Lamp Dimmer Switch Replacement (Right Hand Drive)

Instrument Panel Lamp Dimmer Switch

Instrument Panel Lamp Dimmer Switch

Procedure

  1. Disconnect  electrical connector.
  2. Squeeze tabs on switch to unsnap from housing bracket.

Reading Lamp Bulb Replacement

  1. Dome and Reading Lamp Lens
  2. Reading Lamp Bulb (Qty: 2)

Dome and Reading Lamp Lens Replacement

  1. Dome and Reading Lamp Lens

Dome Lamp Replacement

Preliminary Procedure

Preliminary Procedure

Lower the headliner enough to gain access to the dome lamp housing. Refer to Headlining Trim Panel Replacement.

  1. Dome Lamp Lens
  2. Dome Lamp Switch Bezel
  3. Dome Lamp Housing Assembly

Procedure

  1. Carefully use a flat-bladed tool, and release the tabs retaining the dome  lamp to the headliner.
  2. Disconnect the electrical connector.

Dome Lamp Bulb Replacement

  1. Dome and Reading Lamp Lens
  2. Dome Lamp Bulb
Lighting
Specifications Headlights/Daytime Running Lights (DRL) Schematics Interior Lights Schematics ...

Headlamp Replacement
Preliminary Procedure Remove the front bumper fascia upper bracket. Refer to Front Bumper Fascia Replacement. Headlamp Screw (Qty: 4) Caution: Refer to Fastener Caution in the Preface se ...

Other materials:

Rail Dust Damage Repair
Warning: Refer to Eye Protection Warning in the Preface section. Note: If rail dust has penetrated into the basecoat, the panel requires refinishing. Ensure all the rail dust has been removed prior to refinishing or the rust spots will return. Rail dust damage comes from the tiny iron particles ...

Daytime Running Lamps (DRL)
Daytime Running Lamps can make it easier for others to see the front of your vehicle during the day. Fully functional daytime running lamps are required on all vehicles first sold in Canada. A light sensor on top of the instrument panel makes the DRL work, so be sure it is not covered. The D ...

Airbag System
The vehicle has the following airbags: • A frontal airbag for the driver. •  A frontal airbag for the front outboard passenger. • A knee airbag for the driver. • A knee airbag for the front outboard passenger. • A seat-mounted side impact airbag for the driver. • A seat-mounted side impac ...

© 2011-2024 Copyright www.ccruze.com