Chevrolet Cruze manuals

Chevrolet Cruze Repair Manual: Driver or Passenger Seat Replacement

Chevrolet Cruze Repair Manual / Seats / Seat Hardware, Trim, and Upholstery / Driver or Passenger Seat Replacement

Removal Procedure

Warning: Refer to SIR Warning in the Preface section.

Warning: When carrying a live inflator module, make sure the bag

Warning: When carrying a live inflator module, make sure the bag opening is pointed away from you. This minimizes the chance of injury in the case of an accidental deployment. Never carry the inflator module by the wires. Never carry the inflator module by the connector on the underside of the module.

Make sure that the bag and trim cover are facing up whenever you place a live inflator module on any surface. This is necessary to provide a free space for the bag to expand in the unlikely event of accidental deployment. Never rest the steering column assembly on the steering wheel with the inflator module face down, and the column vertical. This may result in personal injury.

  1. Disable the supplemental inflatable restraint (SIR) system. Refer to SIR  Disabling and Enabling.
  2. Remove the front seat outer recliner upper finish cover (1).
  3. Unscrew the bolt (2)
  4. Remove the seat belt (3) from the front seat.

  1. Unscrew the 2 bolts (1).
  2. Disconnect the wiring harness plug (2) from the belt buckle.
  3. Release and disconnect the wiring harness plug (3) front seat.
  4. Remove the front seat (4) from the guide in front.

Installation Procedure

  1. Perform the front seat track synchronization. Refer to Front Seat  Track Synchronization.
  2. Install the front seat (4) to the guide in front.
  3. Connect and latch the wiring harness plug (3) front seat.
  4. Connect the wiring harness plug (2) from the belt buckle.

Caution: Refer to Fastener Caution in the Preface section.

  1. Tighten the 2 bolts (1).

Tighten 45 N·m (33 lb in)

  1. Install the seat belt (3) to the front seat.
  2. Tighten the bolt (2).

Tighten 9 N·m (80 lb in)

  1. Install the front seat outer recliner upper finish cover (1).
  2. Enable the SIR system. Refer to SIR Disabling and Enabling.

Front Seat Outer Recliner Upper Finish Cover Replacement

  1. Front Seat Outer Recliner Upper Finish Cover Assembly

Front Seat Adjuster Replacement

  1. Front Seat Outer Recliner Upper Finish Cover
  2. Front Seat Adjuster Bolt

Caution: Refer to Fastener Caution in the Preface section.

Tighten 20 N·m(15 lb in)

  1. Front Seat Adjuster
Seat Hardware, Trim, and Upholstery
Specifications ...

Front Seat Track Synchronization
The fore/aft manual adjuster is composed of an inboard track assembly (5), and outboard track (4) assembly, and an adjuster handle (1). Each track assembly is made of an upper track (2) and a ...

Other materials:

Installation Procedure
Remove all mounds or loose pieces of urethane adhesive from the pinch-weld area. Inspect for any of the following problems in order to help prevent future breakage of the window: High weld Solder spots Hardened sealer Any other obstruction or irregularity in the pinch-weld fla ...

Heating and Air Conditioning System Description and Operation
Engine Coolant Engine coolant is the key element of the heating system. The thermostat controls engine operating coolant temperature. The thermostat also creates a restriction for the cooling system that promotes a positive coolant flow and helps prevent cavitation. Coolant enters the heater ...

StabiliTrak® System
The vehicle has a vehicle stability enhancement system called StabiliTrak. It is an advanced computer controlled system that assists with directional control of the vehicle in difficult driving conditions. StabiliTrak activates when the computer senses a difference between the intended path, ...

© 2011-2024 Copyright www.ccruze.com