Chevrolet Cruze manuals

Chevrolet Cruze Repair Manual: Front Brake Rotor Replacement

Chevrolet Cruze Repair Manual / Additional links / Front Brake Rotor Replacement

Special Tools

For equivalent regional tools, refer to Special Tools.

Removal Procedure

Warning: Refer to Brake Dust Warning in the Preface section.

  1. Raise and support the vehicle. Refer to Lifting  and Jacking the Vehicle.
  2. Remove the tire and wheel assembly. Refer to Tire and Wheel Removal and Installation.
  3. Install a C-clamp (1) over the body of the brake caliper, with the C-clamp ends against the rear of the caliper body and the outboard disc brake pad.
  4. Tighten the C-clamp (1) until the caliper piston is compressed into the caliper bore enough to allow the caliper to slide past the brake rotor.
  5. Remove the C-clamp (1).

  1. Remove and DISCARD the brake caliper bracket bolts (1).

Caution: Support the brake caliper with heavy mechanic wire, or

Caution: Support the brake caliper with heavy mechanic wire, or equivalent, whenever it is separated from its mount and the hydraulic flexible brake hose is still connected. Failure to support the caliper in this manner will cause the flexible brake hose to bear the weight of the caliper, which may cause damage to the brake hose and in turn may cause a brake fluid leak.

Note: Do NOT disconnect the hydraulic brake flexible hose from the caliper.

  1. Remove the brake caliper and the caliper mounting bracket as an assembly (1) from the steering knuckle and support the assembly with heavy mechanic's wire, or equivalent. Ensure that there is no tension on the hydraulic brake flexible hose.
  2. Matchmark the position of   the brake rotor to the wheel studs.

  1. Remove the brake rotor screw (2).
  2. Remove the brake rotor (1) from the wheel hub.

Installation Procedure

Note: Whenever the brake rotor has been separated from the hub/axle

Note: Whenever the brake rotor has been separated from the hub/axle flange, any rust or contaminants should be cleaned from the hub/axle flange and the brake rotor mating surfaces. Failure to do this may result in excessive assembled lateral runout (LRO) of the brake rotor, which could lead to brake pulsation.

  1. Using the CH 42450-A resurfacer , thoroughly clean any rust or corrosion from the mating surface of the hub/axle flange (1).
  2. Using the CH 41013 resurfacer , thoroughly clean any rust or corrosion from the mating surface and mounting surface of the brake rotor (2).
  3. Inspect the mating surfaces of the hub/axle flange and the rotor to ensure that there are no foreign particles or debris remaining.
  4. Install the brake rotor to the hub/axle flange. Use the matchmark made prior to removal for proper orientation to the flange.

Caution: Refer to Fastener Caution in the Preface section.

  1. Install the brake rotor screw and tighten to 7 N·m (62 lb in).
  2. If the brake rotor was removed and installed as part of a brake system repair, measure the assembled LRO of the brake rotor to ensure optimum performance of the disc brakes. Refer to Brake Rotor Assembled Lateral Runout Measurement.
  3. If the brake rotor assembled LRO measurement exceeds the specification, bring the LRO to within specifications. Refer to Brake Rotor Assembled Lateral Runout Correction.
  4. Remove the support, and install the brake caliper and the brake caliper bracket as an assembly to the steering knuckle.

  1. Install NEW brake caliper bracket bolts (1) and tighten to  100 N·m (74 lb ft) + 60° + 15°..
  2. Install the tire and wheel assembly. Refer to Tire and Wheel Removal and Installation.
  3. Lower the vehicle.
  4. If the brake rotor was refinished or replaced, or if new brake pads were installed, burnish the pads and rotors. Refer to Brake Pad and Rotor Burnishing.
Power Steering Pump Belt Replacement
Special Tools CH 49800 Installer Power Steering Pump Belt For equivalent regional tools, refer to Special Tools. Removal Procedure Caution: Do not use belt dressing on the drive belt. Belt dressin ...

Front Wheel Drive Shaft Replacement - Left Side
Special Tools CH-313 Slide Hammer CH-6003 Axle Shaft Remover CH-46376 Holding Wrench CH-49400 Hub Spindle Remover DT-6332 Seal Protector EN-956-1 Extension For equivalent regional too ...

Other materials:

Immobilizer Operation
This vehicle has a passive theft-deterrent system. The system does not have to be manually armed or disarmed. The vehicle is automatically immobilized when the key is removed from the ignition. The system is automatically disarmed when the vehicle is started with the correct key. The key uses a ...

Moveable Window Schematics
Defogger Schematics Window System Component Views Window Systems Component Views ...

Installation Procedure
Cut the front compartment front rail in corresponding locations to fit the remaining original panel. The sectioning joint should be trimmed to allow a gap of one-and-one-half-times the metal thickness at the sectioning joint. Create a 50 mm (2 in) backing plate from the unused porti ...

© 2011-2024 Copyright www.ccruze.com