Chevrolet Cruze manuals

Chevrolet Cruze Repair Manual: Front Seat Cushion Cover and Pad Replacement

Chevrolet Cruze Repair Manual / Seats / Seat Hardware, Trim, and Upholstery / Front Seat Cushion Cover and Pad Replacement

Removal Procedure

Warning: Refer to SIR Warning in the Preface section.

Warning: Replace the passenger presence system as a complete assembly to prevent possible injury to the occupant. The bladder, the pressure sensor, the seat cushion, and the control module are assembled and calibrated as a unit. Using only some of the components in the service kit will cause the passenger presence system to operate improperly.

  1. Remove driver or passenger seat. Refer to Driver  or Passenger Seat Replacement.
  2. Remove front seat adjuster handle, if equipped.
  3. Remove front seat recliner handle. Refer to Driver or Passenger Seat Recliner Handle Replacement.
  4. Remove seat cushion inner trim panel. Refer to Front Seat Cushion Inner Trim Panel Replacement.
  5. Remove seat cushion outer trim panel. Refer to Front Seat Cushion Outer Trim Panel Replacement.

  1. Detach cushion cover from backrest below.
  2. Release and disconnect wiring harness plug (1), if equipped.
  3. Remove front seat backrest screw (2) (Qty: 4).
  4. Remove backrest.

  1. Detach cushion cover (1) from seat frame (3) all the way round.
  2. Remove cushion cover (1) with pad (2) from frame (3).
  3. Remove cushion cover (1) from pad (2).

Installation Procedure

  1. Install cushion  cover (1) to pad (2).
  2. Install cushion cover (1) with pad (2) to frame (3).
  3. Attach cushion cover (1) from seat frame (3) all the way round.

  1. Install backrest.

Caution: Refer to Fastener Caution in the Preface section.

  1. Tighten screw (2) (Qty: 4).

Tighten 35 N·m (26 lb ft)

  1. Connect and latch wiring harness plug (1), if equipped.
  2. Attach cushion cover to backrest below.
  3. Install seat cushion outer trim panel. Refer to Front Seat Cushion Outer Trim Panel Replacement.
  4. Install seat cushion inner trim panel. Refer to Front Seat Cushion Inner Trim Panel Replacement.
  5. Install front seat recliner handle. Refer to Driver or Passenger Seat Recliner Handle Replacement.
  6. Install front seat adjuster handle, if equipped.
  7. Install driver or passenger seat. Refer to Driver or Passenger Seat Replacement.
Front Seat Track Synchronization
The fore/aft manual adjuster is composed of an inboard track assembly (5), and outboard track (4) assembly, and an adjuster handle (1). Each track assembly is made of an upper track (2) and a ...

Driver or Passenger Seat Back Cushion Cover and Pad Replacement
Removal Procedure Warning: Refer to SIR Warning in the Preface section. Warning: Replace the passenger presence system as a complete assembly to prevent possible injury to the occupant. The blad ...

Other materials:

Center Pillar Upper Garnish Molding Replacement
Preliminary Procedure Remove the center pillar lower garnish molding. Refer to Center Pillar Lower Ga   rnish Molding Replacement Remove the seat belt from the front seat. Refer to Driver or Passenger Seat Retractor Side Belt Replacement Center Pillar Upper Garnish Mo ...

Electrical System Overload
The vehicle has fuses and circuit breakers to protect against an electrical system overload. When the current electrical load is too heavy, the circuit breaker opens and closes, protecting the circuit until the current load returns to normal or the problem is fixed. This greatly reduces the c ...

Installation Procedure
Cut the body lock pillar outer panel in corresponding locations to fit the remaining original panel. The sectioning joint should be trimmed to allow a gap of one-and-one-half-times the metal thickness at the sectioning joint Create a 50 mm (2 in) backing plate from the unused portio ...

© 2011-2024 Copyright www.ccruze.com