Chevrolet Cruze Repair Manual: Installation Procedure
- Remove rear end upper panel extension (1) from service part.
- Cut the body side inner panel in corresponding locations to fit the
remaining original panel. The sectioning joint should be trimmed to
allow a gap of one-and-one-half-times the metal thickness at the sectioning
joint.
- Create a 50 mm (2 in) backing plate from the unused portion of the
service part.
- Create 5 x 18 mm (4/16 x 11/16 in) slots for MIG-brazing along the
sectioning cut on the remaining original part. Locate these holes
13 mm (1/2 in) from the edge of part and spaced 40 mm (1 1/2 in) apart.
- Prepare all mating surfaces as necessary.
- Fit the backing plates halfway into the sectioning joints, clamp in
place and plug weld to the vehicle.
- Align the body side inner panel.
- Create 6 x 20 mm (4/16 x 12/16 in) slots for MIG-brazing in locations
where you can not apply a resistance spot
welder.
- Clean and prepare the attaching surfaces for spot welding and brazing.
Note: In MIG-brazing areas 50 mm (2 in) must be kept clear of
structural adhesive.
- Apply structural adhesive to all attaching surfaces
- Position the body side inner panel.
- Verify the fit of the panel.
- Clamp the body side inner panel into position.
- Braze accordingly.
- Spot weld accordingly
- To create a solid braze with minimum heat distortion, make 25 mm (1 in)
stitch brazes along the seam with 25 mm (1 in) gaps
between them. Then go back and complete the stitch braze.
- Cut the body lock pillar upper reinforcement in corresponding locations
to fit the remaining original panel. The sectioning joint should
be trimmed to allow a gap of one-and-one-half-times the metal thickness at
the sectioning joint.
- Create a 50 mm (2 in) backing plate from the unused portion of the
service part.
- Create 5 x 18 mm (4/16 x 11/16 in) slots for MIG-brazing along the
sectioning cut on the remaining original part. Locate these holes
13 mm (1/2 in) from the edge of part and spaced 40 mm (1 1/2 in) apart.
- Prepare all mating surfaces as necessary.
- Fit the backing plates halfway into the sectioning joints, clamp in
place and braze to the vehicle.
- Align the body lock pillar upper reinforcement.
- Create 6 x 20 mm (4/16 x 12/16 in) slots for MIG-brazing in locations
where you can not apply a resistance spot welder.
- Clean and prepare the attaching surfaces for spot welding and brazing.
Note: In MIG-brazing areas 50 mm (2 in) must be kept clear of
structural adhesive.
- Apply structural adhesive to all attaching surfaces
- Position the body lock pillar upper reinforcement.
- Verify the fit of the panel.
- Clamp the body lock pillar upper reinforcement into position.
- Braze accordingly.
- Spot weld accordingly.
- Apply the sealers and anti-corrosion materials to the repair area, as
necessary. Refer to Anti-Corrosion Treatment and Repair.
- Paint the repaired area. Refer to Basecoat/Clearcoat Paint Systems.
- Install all related panels and components.
- Connect the negative battery cable. Refer to Battery Negative Cable
Disconnection and Connection.
- Enable the SIR system. Refer to SIR Disabling and Enabling.
Warning: Refer to Approved Equipment for Collision Repair Warning in the
Preface section.
Warning: Refer to Collision Sectioning Warning in the Preface section.
Warning: Refer to Glass and She ...
Note: According to different corrosion warranties, only the
regional mandatory joining methods are allowed. ...
Other materials:
Specifications
Front Door (Diesel)
65 mm
83 mm
Front Door (Diesel)
60 mm
87 mm
Rear Compartment Lid (Diesel)
122 mm
32 mm
Rear Compartment Lid (Ecoline)
162 mm
32 mm
...
Removal Procedure
Warning: Refer to Approved Equipment for Collision Repair Warning in the
Preface section.
Warning: Refer to Glass and Sheet Metal Handling Warning in the Preface section.
Disable the SIR System. Refer to SIR
Disabling and Enabling.
Disconnect the negative battery cable. Refer to ...
Engine Coolant
The cooling system in the vehicle is filled with DEX-COOL engine coolant. This
coolant is designed to remain in the vehicle for 5 years or 240 000 km (150,000
mi), whichever occurs first.
The following explains the cooling system and how to check and add coolant when
it is low. If there is a ...