Chevrolet Cruze Repair Manual: Power Steering Gear Inlet Pipe/Hose Replacement
Removal Procedure
- Remove front bumper fascia. Refer to Front Bumper Fascia Replacement
- Remove as much power steering fluid from the remote power steering fluid
reservoir as possible.
- Place drain pans under the vehicle as needed.
- Remove power steering gear inlet hose bolt (1).
- Remove inlet hose (3) from clip (2).
- Unscrew hollow screw (1).
- Remove gasket (2).
- Remove inlet pipe (3) from power steering pump.
- Unscrew 3 bracket nuts (1).
- Remove power steering gear inlet pipe (2) from vehicle.
- Extract the steering gear oil seal from the steering gear.
Installation Procedure
- Install the NEW steering gear oil seal to the steering gear.
- Ensure the steering gear oil seals are fully seated in the steering
gear.
- Install power steering gear inlet pipe (2) to vehicle.
Caution: Refer to Fastener Caution in the Preface section.
- Install 3 bracket nuts (1) and tighten to 9 N·m (80 lb in).
- Install inlet pipe (3) to power steering pump.
- Install gasket (2).
- Install hollow screw (1) and tighten to 21 N·m (16 lb ft).
- Install inlet hose (3) to clip (2).
- Install power steering gear inlet hose bolt (1) and tighten to 11 N·m
(98 lb in).
- Clean any excess power steering fluid from the vehicle and remove the
drain pans.
- Install front bumper fascia. Refer to Front Bumper Fascia Replacement
- Fill and bleed the power steering system. Refer to Power Steering System
Bleeding
Power Steering Gear Outlet Pipe/Hose Replacement
Preliminary Procedure
- Remove as much power steering fluid from the remote power steering fluid
reservoir as possible.
- Place drain pans under the vehicle as needed.
Power Steering Gear Inlet Hose Bolt
Caution: Refer to Fastener Caution in the Preface section.
Tighten
11 N·m (98 lb in).
Hose Clamp
Procedure
Compress the power steering fluid reservoir outlet hose clamp from the power
steering fluid reservoir.
Power Steering Gear Outlet Hose
Procedure
Fill and bleed the power steering system. Refer to Power Steering System
Bleeding.
Tip
Clean any excess power steering fluid from the vehicle.
Special Tools
CH-804 Drive Axle Seal Clamp Pliers
Removal Procedure
Remove the steering linkage outer tie rod. Refer to Steering Linkage Outer
Tie Rod Replacement.
Remove the steering lin ...
Special Tools
EN 45059 Torque Angle Sensor Kit
For equivalent regional tools, refer to Special Tools.
Removal Procedure
Turn the front wheels to the straight forward position and secure the
...
Other materials:
Service Publications Ordering Information
Service Manuals
Service Manuals have the diagnosis and repair information on the engines, transmission,
axle, suspension, brakes, electrical, steering, body, etc.
Service Bulletins
Service Bulletins give additional technical service information needed to knowledgeably
service General Motors c ...
Air Conditioning Compressor Replacement (1.6L LXT)
Preliminary Procedures
Recover the refrigerant. Refer to Refrigerant Rec overy and
Recharging.
Remove drive belt. Refer to Generator and Air Conditioning Compressor
and Power Steering Pump Belt Replacement.
Raise and support the vehicle. Refer to Lifting and Jacking the Vehic ...
Rear Compartment Lid Replacement
Preliminary Procedure
Remove the rear compartment lid inner panel trim. Refer to Rear Compartment
Lid Inner Panel Trim Replacement.
Rear Compartment Lid Hinge Bolt (Qty: 4)
Caution: Refer to Fastener Caution in the Preface section.
Tighten
9 N·m (80 lb ft)
Rear Compartment Lid
...