Chevrolet Cruze manuals

Chevrolet Cruze Repair Manual: Stabilizer Shaft Replacement

Chevrolet Cruze Repair Manual / Suspension / Front Suspension / Stabilizer Shaft Replacement

Special Tools

For equivalent regional tools, refer to Special Tools.

Removal Procedure

  1. Turn the front wheels to the straight forward position and secure the steering   wheel from moving.

  1. Remove the 2 lower steering intermediate shaft bolts (1).
  2. Remove the steering intermediate shaft from the steering gear.
  3. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle.
  4. Remove the tire and wheel assemblies. Refer to Tire and Wheel Removal and Installation.
  5. Remove the front compartment insulator, if equipped. Refer to Front Compartment Insulator Replacement.
  6. Remove the exhaust flexible pipe. Refer to Exhaust Flexible Pipe Replacement.

  1. Remove lower stabilizer link shaft nut (2) on both sides.
  2. Remove stabilizer link shaft (1) from stabilizer shaft.
  3. Remove stabilizer link shaft (1) from stabilizer.

  1. Remove 4 fasteners (1) of engine side cover on both sides.

.

  1. Remove 4 fasteners (1) of front en 12. gine compartment cover.

  1. Remove the front (1) and the rear (2) transmission mount bracket bolts.

  1. Remove and DISCARD 2 rear suspension frame bolts (2).

Remove rear frame reinforcements (1).

  1. Position and set hydraulic lifter in connection with CH-904 frame and CH-49289-50 adapter (2) onto suspension frame (1). Pull away front engine compartment cover slightly..
  2. Lower  suspension frame max. 55 mm.

  1. Remove the 4 front stabilizer shaft insulator clam bolts (1).
  2. Remove the stabilizer shaft.

Installation Procedure

  1. Install the stabilizer shaft.

Caution: Refer to Fastener Caution in the Preface section.

  1. Install the 4 front stabilizer shaft insulator clam bolts (1) and tighten to 22 N·m (17 lb ft) plus 30 degrees.

  1. Move out the positioning pins (1) of CH 49289 adapter .

  1. Raise the frame (1) carefully, 4. using CH 49289 adapter (2).

Note: Note: Do NOT reuse old bolts

Note: Note: Do NOT reuse old bolts

  1. Install the 2 frame reinforcements (1).
  2. Install the 2 NEW frame rear bolts (2) and tighten to 160 N·m (119 lb ft).

  1. Install the front transmission mount bolt (1) and tighten to 58 N·m (43 lb ft).
  2. Install the rear transmission mount bracket bolt (2) and tighten to 100 N·m (74 lb ft).

  1. Install and tighten 4 fasteners (1) of engine side cover on both sides.

  1. Install and tighten the 4 fasteners (1) of front engine compartment cover.
  2. Install the front compartment insulator, if equipped Front Compartment Insulator Replacement.
  3. Install the exhaust flexible pipe. Refer to Exhaust Flexible Pipe Replacement.

  1. Install and tighten lower stabilizer link shaft nut (2) on both sides to 35 N·m (26 lb ft).
  2. Lower the vehicle.
  3. Install the tire and wheel assemblies. Refer to Tire and Wheel Removal and Installation.
Front Suspension
Specifications Front Suspension Components Drivetrain and Front Suspension Frame Front Stabilizer Shaft Drivetrain and Front Suspension Frame Rear Insulator Front Stabilizer Shaft L ...

Stabilizer Shaft Link Replacement
Preliminary Procedure Raise and support the vehicle. Refer to Lifting   and Jacking the Vehicle. Remove the front tire and wheel assemblies. Refer to Tire and Wheel Removal a ...

Other materials:

Waterleak Test Preparation
GM vehicles are designed to operate under normal environmental conditions. The design criteria for sealing materials and components takes into consideration the sealing forces required to withstand the natural elements. These specifications cannot take into consideration any artificial ...

Brake Fluid
The brake/clutch master cylinder reservoir is filled with DOT 3 brake fluid as indicated on the reservoir cap. There are only two reasons why the brake fluid level in the reservoir might go down: • The brake fluid level goes down because of normal brake lining wear. When new linings are in ...

Headlining Trim Panel Replacement (Without Sunroof)
Warning: Do not attempt to repair or alter the head impact energy-absorbing material glued to the headliner or to the garnish trims. If the material is damaged, replace the headliner and/or the garnish trim. Failure to do so could result in personal injury. Caution: If a vehicle is equip ...

© 2011-2024 Copyright www.ccruze.com