Chevrolet Cruze manuals

Chevrolet Cruze Repair Manual: Battery Negative Cable Disconnection and Reconnection

Chevrolet Cruze Repair Manual / Additional links / Battery Negative Cable Disconnection and Reconnection

Removal Procedure

  1. Turn on the radio and record all of the customer radio station presets.
  2. Ensure that all lamps and accessories are turned off.
  3. Turn the ignition OFF and remove the ignition key.

Warning: Refer to Battery Disconnect Warning in the Preface section.

  1. Loosen the negative battery cable nut (2).
  2. Remove the negative battery cable (1) from the battery.

Installation Procedure

  1. Install the negative battery cable (1) to the battery.

Caution: Refer to Fastener Caution in the Preface section.

  1. Fasten the negative battery cable nut (2) and tighten the nut to 4 N·m (35 lb in).
  2. Insert the ignition key and turn the ignition to the ON position.
  3. Program volatile memory. Refer to Volatile Memory Programming.
  4. Program all of the customer's radio station presets and set the radio clock to the current time.

Exhaust Flexible Pipe Replacement (1.6L LDE, LXV, and 1.8L 2H0)

Warning: Refer to Exhaust Service Warning in the Preface section.

Warning: Refer to Exhaust Service Warning in the Preface section.

Warning: Refer to Protective Goggles and Glove Warning in the Preface section.

Preliminary Procedure

Raise the vehicle by its full height. Refer to Lifting and Jacking the Vehicle.

  1. Exhaust Muffler Insulator (Qty: 2)
  2. Exhaust Flexible Pipe Gasket to Exhaust Rear Muffler
  3. Exhaust Flexible Pipe to Exhaust Rear Muffler Nuts (Qty: 2)

Caution: Refer to Fastener Caution in the Preface section.

Tighten 17 N·m (13 lb ft)

  1. Exhaust Pipe Front Hanger Bracket
  2. Exhaust Pipe Front Hanger Bracket Bolts and Nuts

Tighten 20 N·m (15 lb ft)

  1. Catalytic Converter to Exhaust Flexible Pipe Gasket
  2. Catalytic Converter to Exhaust Flexible Pipe Nuts (Qty: 3)

Tighten 20 N·m (15 lb ft)

  1. Heated Oxygen Sensor

Tighten 40 N·m (30 lb ft)

Additional links
Instrument Cluster Replacement Preliminary Procedure Remove instrument panel lower cluster trim plate. Refer to Instrument Panel Cluster Lower Trim Plate Replacement. Remove instrument p ...

Exhaust Flexible Pipe Replacement (1.6L LXT)
Removal Procedure Warning: Refer to Hot Exhaust System Warning in the Preface section. Warning: Refer to Protective Goggles and Glove Warning in the Preface section. Open the hood. Raise the ...

Other materials:

Driving on Wet Roads
Rain and wet roads can reduce vehicle traction and affect your ability to stop and accelerate. Always drive slower in these types of driving conditions and avoid driving through large puddles and deep-standing or flowing water. WARNING Wet brakes can cause crashes. They might not work as wel ...

Front Side Door Wiring Harness Replacement
Preliminary Procedure Remove the front side door inner panel trim. Refer to Front Side Door Trim Replacement. Front Side Door Wiring Harness Warning: Unless directed otherwise, the ignition and start switch must be in the OFF or LOCK position, and all electrical loads must be OFF before ...

Repairs and Inspections Required After a Collision
Warning: Restraint systems can be damaged in a collision. To help avoid injury and ensure that all parts in need of replacement are replaced: Replace any seat belt system that was in use during the collision serious enough to deploy any automatic restraint device such as air bags and ...

© 2011-2026 Copyright www.ccruze.com