Chevrolet Cruze manuals

Chevrolet Cruze Repair Manual: Windshield Washer Nozzle Hose Replacement

Chevrolet Cruze Repair Manual / Body systems / Wipers and Washers / Windshield Washer Nozzle Hose Replacement

Preliminary Procedure

Preliminary Procedure

  1. Remove the hood insulator. Refer to   Hood Insulator Replacement.
  2. Place a clean container under the front driver side near where the windshield washer nozzle and windshield washer pump hose will be disconnected.
  3. Recover all lost windshield washer solvent.
  1. Windshield Washer Nozzle Hose

Tip

Disconnect the washer hose from both hood mounted washer nozzles.

  1. Windshield Washer Hose Retainer to Hood Hinge
  2. Windshield Washer Nozzle Hose Integral Connector

Tip

Disconnect the hoses in order to remove the windshield washer nozzle hose.

  1. Windshield Washer Pump Hose

Windshield Washer Nozzle Replacement

Preliminary Procedure

Preliminary Procedure

  1. Disconnect the washer  hose from the washer nozzles.
  2. Remove the hood insulator. Refer to Hood Insulator Replacement

Windshield Washer Nozzle Assembly

Tip

Pinch the washer nozzle from the bottom side in order to release the nozzle and push the nozzle outboard from the hood to remove.

Windshield Washer Solvent Container Filler Tube Replacement

Windshield Washer Solvent Container Filler Tube Assembly

Windshield Washer Solvent Container Filler Tube Assembly

Procedure

  1. Pull the upper tube assembly from the lower washer container and inspect the grommet (1), replace if damaged.

    Refer to Windshield Washer Solvent Container Grommet Replacement.

  2. Insert the tube rib flush to the top seal at the lower container.

Windshield Washer Solvent Container Grommet Replacement

Preliminary Procedure

Preliminary Procedure

Remove the windshield washer solvent container filler tube assembly. Refer to Windshield Washer Solvent Container Filler Tube Replacement

  1. Windshield Washer Solvent Container Grommet
Wipers and Washers
Specifications Wiper/Washer Schematics Windshield Wiper and Washer Switch Replacement Preliminary Procedure Remove the steering column trim covers. Refer to Steering Column Low ...

Windshield Washer Pump Replacement
Removal Procedure Remove the front wheelhouse liner. Refer to Front Wheelhouse Liner Replacement. Disconnect the washer pump electrical connector (1). Disconnect the washer pump hose (2 ...

Other materials:

Rear Bumper Fascia Replacement
Preliminary Procedure Remove the tail lamps. Refer to Tail Lamp Replacement. Rear Bumper Fascia Retainer (Qty: 2) Rear Wheelhouse Liner Bolt (Qty: 6) Caution: Refer to Fastener Caution in the Preface section. Tighten 2.5 N·m (23 lb in) Rear Bumper Fascia Procedure Pull th ...

Installation Procedure
Remove rear end upper panel extension (1) from service part. Cut Cut the body side inner panel in corresponding locations to fit the remaining original panel. The sectioning joint should be trimmed to allow a gap of one-and-one-half-times the metal thickness at the sectioni ...

Antilock Brake System (ABS) Warning Light
The Antilock Brake System (ABS) light comes on briefly when the engine is started. If the light does not come on, have it fixed so it will be ready to warn if there is a problem. If the ABS light comes on and stays on while driving, stop as soon as possible and turn the ignition off. Start ...

© 2011-2023 Copyright www.ccruze.com