Chevrolet Cruze Repair Manual
- Preface
- Definition of Danger, Warning, Caution, and Note
- Battery Disconnect Warning
- Fuel and Evaporative Emission Pipe Warning
- Halogen Bulb Warning
- Relieving Fuel Pressure Warning
- SIR Inflator Module Handling and Storage Warning
- Steering Angle Sensor Calibration Warning
- Work Stall Test Warning
- Heated Oxygen and Oxygen Sensor Caution
- Steering Column in Lock Position Caution
- Test Probe Caution
- General Information
- Body hardware and trim
- Exterior Trim
- Floor Coverings and Headlinings
- Instrument Panel and Console Trim
- Interior Trim and Paneling
- Body repair
- Bolted Exterior Body Panels and Closures
- Bumpers and Fascias
- Front Bumper Energy Absorber Bracket Replacement
- Front Bumper Fascia Replacement
- Front Bumper Fascia Guide Replacement
- Rear Bumper Fascia Replacement
- Rear Bumper Fascia Guide Replacement
- Rear Bumper Fascia Outer Guide Replacement
- Rear Bumper Impact Bar Replacement
- Collision Repair
- Frame and Underbody
- Paint and Coatings
- Plastic Panel Information and Repair
- Body systems
- Roof
- Seatbelts
- Repairs and Inspections Required After a Collision
- Seat Belt Latch Stop Installation
- Seat Belt System Description and Operation
- Seats
- Restraints
- SIR Identification Views
- SIR Service Precautions
- Front End Inflatable Restraint Discriminating Sensor Replacement
- Inflatable Restraint Side Impact Sensor Replacement
- Steering Wheel Inflatable Restraint Module Replacement
- Steering Wheel Inflatable Restraint Module Coil Replacement
- Inflatable Restraint Steering Wheel Module Coil Centering
- Driver or Passenger Seat Side Inflatable Restraint Module Replacement
- Roof Side Rail Inflatable Restraint Module Replacement
- Driver or Passenger Seat Retractor Side Belt Replacement
- Repairs and Inspections Required After a Collision
- Inflatable Restraint Module Handling and Scrapping
- Pretensioner Handling and Scrapping
- SIR System Description and Operation
- SIR Disabling and Enabling
- Steering
- Suspension
- HVAC System
- Refrigerant Recovery and Recharging
- Air Conditioning Compressor Replacement (1.6L LDE, LXV, and 1.8L 2H0)
- Air Conditioning Compressor Replacement (1.6L LXT)
- Air Conditioning Compressor and Condenser Hose Replacement (1.6L LXT)
- Air Conditioning Compressor and Condenser Hose Replacement (1.6L LDE, LXV, and 1.8L 2H0)
- Air Conditioning Evaporator Hose Assembly Replacement
- Air Conditioning Condenser Replacement (1.6L LDE, LXT, LXV, and 1.8L 2H0)
- Instrument Panel Outer Air Outlet Replacement - Left Side
- Floor Air Outlet Replacement
- Instrument Panel Outer Air Outlet Duct Replacement
- Floor Air Outlet Duct Replacement - Right Side (Right Hand Drive)
- Heating and Air Conditioning System Description and Operation
- Additional links
- Battery Negative Cable Disconnection and Reconnection
- Exhaust Flexible Pipe Replacement (1.6L LXT)
- Power Steering Pump Belt Replacement
- Front Brake Rotor Replacement
- Front Wheel Drive Shaft Replacement - Left Side
- Front Wheel Drive Shaft Replacement - Right Side
- Rear Brake Rotor Replacement
- Brake Drum Replacement
- Drive Belt Replacement
- Generator Air Conditioning Compressor,Power Steering Pump Belt Replacement
Trademarks and License Agreements
FCC Information
See “Radio Frequency Statement” in the owner manual for information regarding
Part 15 of the Federal Communications Commission (FCC) rules and with Industry Canada
Standards RSS-G ...
Preface
...
Other materials:
Installation Procedure
Drill 8 mm (5/16 in) for plug welding along the edges of the drivetrain
and front suspension frame front support as noted from the
original panel.
Clean and prepare the attaching surfaces for welding.
Position the drivetrain and front suspension frame front suppor ...
Headlamps, Front Turn Signal and Parking Lamps
1. Parking/Turn Signal Lamp
2. High-Beam Headlamp/ Low-Beam Headlamp and DRL
High-Beam Headlamp/ Low-Beam Headlamp and DRL
1. Open the hood
2. For the driver side bulb, remove the windshield washer bottle filler neck by
firmly pulling it straight up and out of the bottle.
3. Remove the co ...
Headlamp Aiming Procedure
Open the hood.
Measure from the floor to the center of the headlamp bulb. Some
headlamps have an aim dot marked on the headlamp lens.
At the screen, measure from the floor and place the horizontal tape at
the measured distance.
Measure from the reference line on the floor to the le ...
