Chevrolet Cruze Repair Manual: Additional links
Instrument Cluster Replacement
Preliminary Procedure
- Remove instrument panel lower cluster trim plate. Refer to Instrument Panel Cluster Lower Trim Plate Replacement.
- Remove instrument panel steering column upper trim cover. Refer to Steering Column Upper Trim Cover Replacement.
- Instrument Cluster Screw (Qty: 2)
Caution: Refer to Fastener Caution in the Preface section.
Tighten 2.5 N·m (22 lb in)
- Instrument Cluster Assembly
Procedure
- Disconnect electrical components.
- After repairs, refer to Control Module References
Radio Control Module Replacement
Preliminary Procedures
Remove instrument panel center upper molding. Refer to Instrument Panel Center Upper Molding Replacement
- Radio Control Module Bolts (Qty: 2)
Caution: Refer to Fastener Caution in the Preface section.
Tighten 2.5 N·m(22 lb in)
- Radio Control Module
Procedure
Disconnect electrical components.
Radio Replacement
Preliminary Procedure
- Disconnect the battery negative cable. Refer to Battery Disconnect Warning
- Remove radio control module. Refer to Radio Control Module Replacement
- Radio Bolts (Qty: 4)
Caution: Refer to Fastener Caution in the Preface section.
Tighten 2.5 N·m(22 lb in)
- Radio Bolt Washer (Qty: 4)
- Radio Assembly
Procedure
- Disconnect electrical components.
- After repairs, refer to Control Module References for programming and set up information.
Radiator Support Bracket Replacement
Preliminary Procedure
Remove the front bumper fascia. Refer to Front Bumper Fascia Replacement.
- Radiator Support Bracket Bolt
Caution: Refer to Fastener Caution in the Preface section.
Tighten 22 N·m (17 lb ft)
- Radiator Support Bracket
Procedure
Pull the radiator forward until the bracket is reachable.
- Battery Negative Cable Disconnection and Reconnection
- Exhaust Flexible Pipe Replacement (1.6L LXT)
- Power Steering Pump Belt Replacement
- Front Brake Rotor Replacement
- Front Wheel Drive Shaft Replacement - Left Side
- Front Wheel Drive Shaft Replacement - Right Side
- Rear Brake Rotor Replacement
- Brake Drum Replacement
- Drive Belt Replacement
- Generator Air Conditioning Compressor,Power Steering Pump Belt Replacement
Heating and Air Conditioning System Description and Operation
Engine Coolant
Engine coolant is the key element of the heating system. The thermostat
controls engine operating coolant temperature. The thermostat
also creates a restriction for the cooling syst ...
Battery Negative Cable Disconnection and Reconnection
Removal Procedure
Turn on the radio and record all of the customer radio station presets.
Ensure that all lamps and accessories are turned off.
Turn the ignition OFF and remove the ignition ke ...
Other materials:
Removal Procedure
Warning: Refer to Approved Equipment for Collision Repair Warning in the
Preface section.
Warning: Refer to Collision Sectioning Warning in the Preface section.
Warning: Refer to Glass and Sheet Metal Handling Warning in the Preface section.
Disable the SIR System. Refer to SIR Dis ...
Front Fender Emblem/Nameplate Replacement (1.8L 2H0 or 2.0L Diesel)
Front Fender Emblem Assembly
Caution: Refer to Exterior Trim Emblem Removal Caution in the
Preface section.
Procedure
The part and surface should be 21°C (70°F) prior to installation. The
vehicle should remain 21°C (70°F) for
one hour after assembly to allow adhesive to develop suff ...
Daytime Running Lamps (DRL)
Daytime Running Lamps can make it easier for others to see the front of your
vehicle during the day. Fully functional daytime running lamps are required on all
vehicles first sold in Canada.
A light sensor on top of the instrument panel makes the DRL work, so be sure
it is not covered.
The D ...
